50 l INOX/stal nierdzewna zbiornik ciśnieniowy rozszerzenie krajowa pompa wodna EPDM
119,99 €*
Ceny zawierają podatek VAT + Koszty wysyłki
Natychmiast dostępny, czas dostawy 2 - 3 days(1)
• Stainless steel pressure vessel holds 50 litres
• 32.89-mm (1″) thread connection
• EPDM rubber membrane
• For domestic waterworks
• Vertical mounting
This stainless-steel pressure vessel (type 50 LVS) will be delivered including the EPDM rubber membrane. The vessel is designed for a maximum pressure of 5.4 bar and will be delivered for a vertical positioning. The vessel is checked for tightness with up to 5.4 bar water pressure by the producer.
It has a 32.89–33.25-mm (1″) pump connector. The pressure vessel additionally has an integrated valve (Schrader valve/car tyre valve) to regulate the counter-pressure in the space between tank and membrane.
These vessels are made of quality-steel sheets and are welded according to UNI-EN standards and equipped with a heat and ageing resistant EPDM rubber membrane. The membrane can easily be exchanged.
About ethylene propylene diene monomer rubber:
The EPDM rubber belongs to the group of elastomers. This synthetic material is resistant to hot air, weathering, and ozone. The elastomer shows low gas permeability, good resistance to chemicals as well as up to 100 °C heat. Additionally, it is very good noise and shock energy absorption qualities.
In the low temperature range, the rubber remains elastic up to −70 °C. It is mainly used for air hoses and inner cores of tyres, bladders, steam hoses, and linings for tanks. Further fields of application are foils, membranes, non-vulcanised sealants and bands.
About the pre-charge in the pressurised vessel:
The pre-charge pressure should be set approximately 0.1–0.2 bar lower than the switch-on pressure of the pump and has to be checked regularly. Any failure of observance may cause damage on the EPDM rubber diaphragm of the pressure vessel.
A more accurate calculation results from the formula “switch-on pressure of the pump x 0.9.” Example: Switch-on pressure of the pressure switch of the domestic waterworks is set to 1.5 bar: 1.5 bar x 0.9 = 1.35 bar. This means that the pressure can be set from 1.3–1.4 bar.
Important: The pressure of the vessel should only be inflated or deflated after the pressure to the water system has been released beforehand.
Attention: It is necessary to have released the air and water pressure before opening of the pressure vessel!
Abmessungen: | 1230 x 330 x 330 mm |
---|---|
Betriebsdruck: | 5.4 Bar |
Druck: |
5,4 bar Wasserdruck Luftdruck 1.8 / N2-Vordruck: ca. 2 bar |
Farbe: | grau |
Fassungsvermögen in Liter: | 50 Liter |
Luftdruck: | 1.8 Bar |
Material: | Edelstahl 304 |
Material Membran: | Ethylen-Propylen-Dien-Kautschuk (EPDM) |
Materialstärke: | 1 Millimeter |
Max. temperature: | 99 °C |
Membran: | Butylkautschuk (auswechselbar) |
Min. temperature: | 4 °C |
Produktart: | Hauswasserwerk |
Stickstoff Vordruck: | 2 Bar |
max. Druck (bar): | 5.6 Bar |
präzise Produktart: | Membrankessel |
Ersatzteile
Dostępny, czas dostawy 2 - 3 days
• For 24-100 Liter Pressure Vessels
Dostępny, czas dostawy 2 - 3 days
• for 24-100 Liter Pressure Vessels
• Material: Stainless Steel
Dostępny, czas dostawy 2 - 3 days
• For 24 – 100 litre pressure vessels
• Outer thread ⌀ ½ inch and ⌀ ⅜ inch
• Inner thread ⌀ ⅜ inch and ⌀ ¼ inch
• Space-saving and durable
Dostępny, czas dostawy 2 - 3 days
• For 24–100 litre pressure vessels
• Outer thread ⌀ 1 inch (32.89 mm)
• Inner thread ⌀ ⅜ inch (16.41 mm)
• Space-saving and durable
Dostępny, czas dostawy 2 - 3 days
• For pressure tank vessel
• Expansion for domestic waterworks
Dostępny, czas dostawy 2 - 3 days
• For 24-100 Liter Pressure Vessels
Dostępny, czas dostawy 2 - 3 days
• for 24-100 Liter Pressure Vessels
Dostępny, czas dostawy 2 - 3 days
• for 24-100 Liter Pressure Vessels
Dostępny, czas dostawy 2 - 3 days
• 1x 32,89 mm (1″) ET
• 1x 12,91 mm (¼″) ET
• i.E. Domestic Waterworks, Pressure Vessels
Dostępny, czas dostawy 2 - 3 days
• For 24-100 Liter Pressure Vessels
Dostępny, czas dostawy 2 - 3 days
• For 24-100 Liter Pressure Vessels
Empfehlung: Membrankessel
Dostępny, czas dostawy 2 - 3 days
• 32.89-mm (1″) thread connection
• EPDM rubber membrane
• For domestic waterworks
• Vertical mounting
Dostępny, czas dostawy 2 - 3 days
• 32.89-mm (1″) thread connection
• EPDM rubber thread
• For domestic waterworks
• Vertical mounting
Dostępny, czas dostawy 2 - 3 days
• 32.89-mm (1″) thread connection
• Diameter holes: 9 x 20 mm
• Hole spacing long: 315 x 255 mm
• EPDM rubber membrane
• Membrane boiler for domestic waterworks
• Horizontal with pump attachment plate
Dostępny, czas dostawy 2 - 3 days
• 32.89-mm (1″) thread connection
• EPDM rubber membrane
• For domestic waterworks
• Horizontal with pump attachment plate
Dostępny, czas dostawy 2 - 3 days
• 32,89 mm (1") thread connection
• Membrane included
• For Domestic waterworks
• Horizontal with pump-fixation
Dostępny, czas dostawy 2 - 3 days
• 32.89-mm (1″) thread connection
• EPDM membrane
• For domestic waterworks
• Horizontal with pump fixation
Dostępny, czas dostawy 2 - 3 days
• Przyłącze gwintowe 32,89 mm (1″)
• Membrana EPDM
• Zbiornik membranowy do hydroforów domowych
• Wykonanie pionowe
Dostępny, czas dostawy 2 - 3 days
• Przyłącze gwintowe 32,89 mm (1″)
• Membrana EPDM
• Zbiornik membranowy do hydroforów domowych
• Wykonanie pionowe
Dostępny, czas dostawy 2 - 3 days
• Przyłącze gwintowe 32,89 mm (1″)
• Membrana EPDM
• Zbiornik membranowy do hydroforów
• Poziomo z płytą mocującą hydrofor
Dostępny, czas dostawy 2 - 3 days
• Złącze gwintowe o rozmiarze 32,89 mm (1″)
• Średnica otworów: 9 mm
• Odstęp między otworami długość: 315 x 240 mm
• Membrana EPDM
• Zbiornik membranowy do hydroforów domowych
Empfehlung: Pumpe Hauswasserwerk
Dostępny, czas dostawy 2 - 3 days
• Makes rainwater available for house and garden
• Handle for comfortable transportation
• Built-in filter and pressure gauge
• Built-in pressure switch
Dostępny, czas dostawy 2 - 3 days
• Max. Suction Height 7 m
• Max. Delivery Head: 46 m
• with Pump Control SK-13
Dostępny, czas dostawy 2 - 3 days
• Power consumption 3200 l/h
• Delivery head 38 m
• Suction head 8 m
• Power 800 watts
• Thermal protection
• Thread 1 inch
Dostępny, czas dostawy 2 - 3 days
• Output: 1200 W
• 19 L pressure tank volume
• Pressure gauge
• Built-in pressure switch
Dostępny, czas dostawy 2 - 3 days
• Output: 1300 W
• Built-in filter and pressure gauge
• Integrated pressure switch
• 19 L pressure tank volume
Dostępny, czas dostawy 2 - 3 days
• Max. Suction Height 7 m
• Max. Delivery Head: 46 m
Dostępny, czas dostawy 2 - 3 days
• For fresh, clear and well water
• 600 W power output
• Max. discharge head 35 m
• Flow rate 2800 litres per hour
Dostępny, czas dostawy 2 - 3 days
• For fresh, clear and well water
• 600 W power output
• Max. discharge head 35 m
• Flow rate 2800 litres per hour
Dostępny, czas dostawy 2 - 3 days
• For fresh, clear and well water
• 1200 W power output
• Max. discharge head 48 m
• Flow rate 3800 litres per hour
Dostępny, czas dostawy 2 - 3 days
• For fresh, clear and well water
• 1200 W power output
• Max. discharge head 48 m
• Flow rate 3800 litres per hour
Dostępny, czas dostawy 2 - 3 days
• Max. Suction Height 7 m
• Max. Delivery Head: 45 m
• with Pump Control SK-13
Dostępny, czas dostawy 2 - 3 days
• Max. Suction Height 8 m
• Max. Delivery Head: 50 m
Dostępny, czas dostawy 2 - 3 days
• Output: 1100 W
• Built-in filter unit
• Extra large inlet
• 32.89 mm (G1") connection
Dostępny, czas dostawy 2 - 3 days
• Moc: 1200 W
• Manometr
• Z wbudowanym przełącznikiem ciśnieniowym
• Zbiornik membranowy o pojemności 19 l
Dostępny, czas dostawy 2 - 3 days
• Flowrate up to 2800 l/h
• With manometer and pressure switch
• Pumps rainwater, process water and groundwater
• Reduces the energy consumption
Dostępny, czas dostawy 2 - 3 days
• Flowrate up to 3000 l/h
• With manometer and pressure switch
• Pumps rainwater, process water and groundwater
• Reduces the energy consumption
Empfehlung: Membrankessel Zubehör
Dostępny, czas dostawy 2 - 3 days
• 1x 32,89mm (1") ET
• i.E. Domestic Waterworks, Pressure Vessels
Dostępny, czas dostawy 2 - 3 days
• 1x 32,89 mm (1″) ET
• 1x 12,91 mm (¼″) ET
• i.E. Domestic Waterworks, Pressure Vessels
Dostępny, czas dostawy 2 - 3 days
• 1x 32,89 mm (1″) ET
• 1x 12,91 mm (¼″) FT
• i.E. Domestic Waterworks, Pressure Vessels
Dostępny, czas dostawy 2 - 3 days
• 1x 32,89mm (1") ET
• 1x 12,91mm (1/4") FT
• 1x 12,91mm (1/4") ET
• i.E. Domestic Waterworks, Pressure Vessels
Dostępny, czas dostawy 2 - 3 days
• DN25 33,7mm (1 Inch) Female Thread
• DN25 33,7mm (1 Inch) Male Thread
• Braided with stainless steel
• E.g. Pressure vessels in domestic waterworks
Treść: 0.5 metre(s) (27,98 €* / 1 metre(s))
Dostępny, czas dostawy 2 - 3 days
• 32.89 mm (G1″) IT & 32.89 mm (G1″) ET
• Braided with stainless steel
• E.g. Pressure vessels in domestic waterworks
Dostępny, czas dostawy 2 - 3 days
• 0–12 bar resp. 0–170 PSI
• ø 50 mm Pressure Gauge radial
• i.E. Domestic Waterworks, Pressure Vessels
Dostępny, czas dostawy 2 - 3 days
• Inside Ø of 25mm and outside Ø of 33mm
• Braided with stainless steel
• Rubber hose inside
• For membrane boilers, domestic waterworks, etc.
Treść: 0.3 metre(s) (21,63 €* / 1 metre(s))
Dostępny, czas dostawy 2 - 3 days
• Inside Ø of 25mm and outside Ø of 33mm
• Braided with stainless steel
• Rubber hose inside
• For membrane boilers, domestic waterworks, etc.
Treść: 0.6 metre(s) (19,42 €* / 1 metre(s))
Dostępny, czas dostawy 2 - 3 days
• Inside Ø of 25mm and outside Ø of 33mm
• Braided with stainless steel
• Rubber hose inside
• For membrane boilers, domestic waterworks, etc.
Treść: 0.7 metre(s) (22,84 €* / 1 metre(s))
Dostępny, czas dostawy 2 - 3 days
• Inside Ø of 25mm and outside Ø of 33mm
• Braided with stainless steel
• Rubber hose inside
• For membrane boilers, domestic waterworks, etc.
Treść: 0.8 metre(s) (21,24 €* / 1 metre(s))
Dostępny, czas dostawy 2 - 3 days
• 0-10 bar resp. 0-140 PSI
• Ø 50mm Pressure Gauge axial
• i.E. Domestic Waterworks, Pressure Vessels
Dostępny, czas dostawy 2 - 3 days
• 0-12 bar resp. 0-170 PSI
• Ø 50mm Pressure Gauge radial
• i.E. Domestic Waterworks, Pressure Vessels
Dostępny, czas dostawy 2 - 3 days
• 0-12 bar resp. 0-180 PSI
• Ø 50mm Pressure Gauge axial
• i.E. Domestic Waterworks, Pressure Vessels
Dostępny, czas dostawy 2 - 3 days
• 1/2″ male thread (20.95 mm) and 1/2″ union nut (18.64 mm)
• Connection hose with DN13 and 100 cm length
• Resistant to pressure, kinking, and corrosion
• Ideal for fittings, etc. – with DVGW certificate
Dostępny, czas dostawy 2 - 3 days
• 1/2″ union nut (18.64 mm) and 3/4″ union nut (24.12 mm)
• Connection hose with DN13 and 100 cm length
• Resistant to pressure, kinking, and corrosion
• Ideal for fittings, etc. – with DVGW certificate
Dostępny, czas dostawy 2 - 3 days
• 3/4″ male thread (26.44 mm) and 1/2″ union nut (18.64 mm)
• Connection hose with DN13 and 100 cm length
• Resistant to pressure, kinking, and corrosion
• Ideal for fittings, etc. – with DVGW certificate
Dostępny, czas dostawy 2 - 3 days
• 3/4″ union nut (24.12 mm) and 1/2″ male thread (20.95 mm)
• Connection hose with DN13 and 100 cm length
• Resistant to pressure, kinking, and corrosion
• Ideal for fittings, etc. – with DVGW certificate
Dostępny, czas dostawy 2 - 3 days
• 3/4″ union nut with elbow (24.12 mm) and 1/2″ male thread (20.95 mm)
• Connection hose with DN13 and 1000 mm length
• Resistant to pressure, kinking, and corrosion
• Ideal for fittings, etc. – with DVGW certificate
Dostępny, czas dostawy 2 - 3 days
• 3/4″ union nut with elbow (24.12 mm) and 1/2″ union nut (18.64 mm)
• Connection hose with DN13 and 1000 mm length
• Resistant to pressure, kinking, and corrosion
• Ideal for fittings, etc. – with DVGW certificate
Dostępny, czas dostawy 2 - 3 days
• 3/4″ union nut with elbow (24.12 mm) and 3/4″ union nut (24.12 mm)
• Connection hose with DN13 and 1000 mm length
• Resistant to pressure, kinking, and corrosion
• Ideal for fittings, etc. – with DVGW certificate
Dostępny, czas dostawy 2 - 3 days
• 2 connections: 1/2″ union nut (UN) (18.64 mm)
• Connection hose with 13DN inner diameter and 100 cm length
• Resistant to pressure, kinking, and corrosion
• Ideal for fittings, etc. – with DVGW certificate
Dostępny, czas dostawy 2 - 3 days
• 3/4″ union nut (24.12 mm) and 3/4″ male thread (26.44 mm)
• Connection hose with DN19 and 100 cm length
• Resistant to pressure, kinking, and corrosion
• Ideal for fittings, etc. – with DVGW certificate
Dostępny, czas dostawy 2 - 3 days
• 2 connections: 3/4″ union nut (UN) (24.12 mm)
• Connection hose with 19DN inner diameter and 100 cm length
• Resistant to pressure, kinking, and corrosion
• Ideal for fittings, etc. – with DVGW certificate